Showing results: 1501 - 1515 of 2457 items found.
-
Curtiss-Wright Defense Solutions
Our SWaP-optimized 3U VPX rugged mission computer systems are pre-integrated and pre-validated to reduce your cost, risk, and time to market. These systems are based on open standards to meet Modular Open Systems Approach (MOSA) requirements and qualified for temperature extremes, high altitudes, voltage spikes, shock, vibration, and more.
-
1-4kva -
Shenzhen Setec Power Co., Ltd.
1. With micro-CPU control, the circuit is simple and reliable. High efficiency >85%. Adopting SPWM technology, with the output is pure sine wave with stabilized voltage and frequency,filtering noise and low distortion. 2. 1-4kva pure sine wave inverter built-in bypass switch, it can quickly switch between the mains and the inverter.
-
SF600 -
Shanghai Launch Electric Co., Ltd.
This device is specially designed to control temperature for insulation oil measuring electrode. It could be used together with universal cylinder insulation oil electrode. This device ensures that the insulation oil will get a required temperature and keep at this temperature for long. Thus tgδ and εr could be measured through high voltage electrical bridge.
-
N6700 -
Keysight Technologies
Keysight high performance DC power supplies offer speed and accuracy for test optimization. The single output, 200 W, GPIB 6641A-6645A provide fast, low-noise outputs; analog control of output voltage and current; fan-speed control to minimize acoustic noise; as well as parallel and series connections of multiple units.
-
72-8110 -
Tenma
The 72-8110 is a compact switch mode Power Supply features a very compact footprint that makes it an ideal match for portable communications equipment. Its 50% duty cycle surge rating is comes in handy in demanding transmitting situations. It is also perfect for two-way radio (including HF) and audio equipment including auto sound and multimedia systems. This fixed voltage switch mode power supply is designed with high RFI stability and is especially suitable for two-way radio and communications equipment. Constant current circuitry is used for overload, short-circuit and over-temperature protection. Output current and voltage drop to a safe level when any fault occurs. This power supply also has over voltage protection to prevent connected equipment from damage.
-
PQPro -
CANDURA Instruments
The PQPro™ is a portable 8 channel (4 voltage and 4 current) power quality analyzer that can stream high resolution waveform and RMS data to high capacity removable SD memory cards. Sampling rate can be adjusted from 64 samples per cycle to 1024 samples per cycle. The PQPro™ is in a rugged weatherproof enclosure that can be left recording in all kinds of environments - from the top of a utility pole to the bottom of an underground mine shaft!
-
WIKA Alexander Wiegand SE & Co. KG
Thermocouples are temperature sensors that generate a voltage directly dependent on temperature. Compared to resistance thermometers, they are particularly suited for high temperatures up to 1,700 °C. Instrument designs from mineral-insulated sheathed cable are very resistant against extremely high vibration loads (depending on instrument model, sensor element and wetted materials). The accuracy classes 1 and 2 apply for thermocouples in accordance with IEC 60584 as well as the standard and special classes in accordance with ASTM E230.
-
40-614-009 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-013 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-018 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-006 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-020 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-017 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-008 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.
-
40-614-005 -
Pickering Interfaces Ltd.
The 40-614 High Density 2 Amp multiplexer module is available in 20 configurations. All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 200VDC/140VACThe module is suitable for signal routing in ATE and data acquisition systems. User connections are made via a front panel 160-pin DIN 41612 connector which is fully supported by our range of cabling and connector solutions.